All lithium batteries must be charged in a LiPo safe charging container such as a “LiPo Bag” or a “Bat Safe” charging case.

Touring Car

USGT

Motor: any ROAR approved 21.5 motor with ROAR approved tuning rotor
ESC: any ROAR approved non-timing ESC in blinky mode
Battery: any 2s LiPo
Tire: Ride RIE24025 tire and inserts (available though Gravity R/C
Bodies: No WGT, ROAR T2, Truck or bodies intended for oval or off-road. Bodies must completely cover the tires.
Maximum Battery Voltage: - 8.40
Minimum Ride Height 5mm
Minimum Weight 1350g
Maximum Width 200mm
Body height/wing - any scale molded wing can be used Lexan are limited to 10mm maximum height including side dams

Motor: any ROAR approved 25.5 motor with ROAR approved 12.3 tuning rotor
ESC: any ROAR approved non-timing ESC in blinky mode
Battery: any 2s LiPo with a maximum of 6000 mah
Tire / Rim: Protoform 26mm Fronts and Protoform 31mm Rears or Gravity G-Spec VTA tires
Bodies: USVTA approved body with numbers on sides and hood and deck lid. All cars must have a driver figure.
Maximum Battery Voltage: - 8.40
Minimum Ride Height 5mm
Minimum Weight 1425g
Maximum Width 200mm
Chassis: Any era or Brand 4wd chassis is allowed
Body height/wing -Body provided deck lid spoilers allowed (not wings). No additional skirts or raised / extended wing or air control surfaces allowed. Body must be trimmed at body trim lines. Front spoiler may be extended into the body to provide durability. Full rear bumper is required. It is highly preferred that bodies are detailed in race type paint schemes.

Motor: any ROAR approved 25.5 motor with ROAR approved tuning rotor
ESC: any ROAR approved non-timing ESC in blinky mode
Battery: any 2s LiPo
Tire: Ride RIE24025 tire and inserts (available though Gravity R/C
Bodies: No WGT, ROAR T2, Truck or bodies intended for oval or off-road. Bodies must completely cover the tires.
Maximum Battery Voltage: - 8.40
Minimum Ride Height 5mm
Minimum Weight 1320g
Maximum Width 200mm
Body height/wing - any scale molded wing can be used Lexan are limited to 10mm maximum height including side dams

Motor: any ROAR approved 21.5 motor with ROAR approved tuning rotor
ESC: any ROAR approved non-timing ESC in blinky mode
Battery: any 2s LiPo
Tire: Ride RIE24025 tire and inserts (available though Gravity R/C
Bodies: No WGT, ROAR T2, Truck or bodies intended for oval or off-road. Bodies must completely cover the tires.
Maximum Battery Voltage: - 8.40
Minimum Ride Height 5mm
Minimum Weight 1320g
Maximum Width 200mm
Body height/wing - any scale molded wing can be used Lexan are limited to 10mm maximum height including side dams

Motor: any ROAR approved 25.5 motor with ROAR approved 12.3 tuning rotor
ESC: any ROAR approved non-timing ESC in blinky mode
Battery: any hard case 2s LiPo
Tire / Rims: CRC or TCS on UF1 style wheel (single nut retention front and rear)
Bodies: UF1 approved, year 2000 or newer bodies.
Maximum Battery Voltage: - 8.40
Minimum Ride Height 3mm
Minimum Weight 1050g
Maximum Width 290mm
Minimum Body / Wing - Rear wing must be no higher than the body’s air scoop

Motor any ROAR approved 17.5 motor and ROAR approved tuning rotor
ESC any ROAR approved non-timing ESC in it’s approved blinky mode
Battery any hard cased 1s Lipo
Tires/ Rims CRC spec or TCS tires Fronts on front, rears on rear
Body approved body list only. (Body List) Bodies must not be cut lower than the trim line therefore controlling height. Bodies that looked slam will be checked
Maximum Battery Voltage: - 4.20
Minimum Ride Height 5mm
Minimum Weight 1025g

Legal kits: Item 58632 Team Hahn Racing MAN TGS (TT-01 type E chassis), 58642 Team Reinert Racing MAN TGS (TT-01 type E chassis) 58661 Buggyra Racing Fat Fox (TT-01 type E chassis) and 58683 Tankpool24 Mercedes Actros (TT-01 type E chassis)
The kit must be built EXACTLY per the instruction manual.
The ONLY Hop-Op Options permitted are Ball Bearings (ANY BRAND) and any Tamiya servo saver.
Must use the stock pinion and spur gear.
Must use the kit supplied Tamiya TBLE-02S ESC
Must use the kit supplied motor (item 54358 RS-540 Torque-Tuned Motor)
Battery connector on ESC may be changed to DEANS type.
The Motor Bullet Connectors may not be removed.
The ESC & Motor wires may not be shortened!
All body parts must be used.
All screws in the kit must be used. You may not omit screws to change the handling of the truck.
No Minimum or Maximum Weight: No weights of ANY KIND may be put on the truck for ballast.
Adding FOAM material to the kit foam bumper is permitted. You may also use item 54819 Urethane Bumper XL in place of the stock size bumper.
Must use kit type tires and wheels. Note: Kit tires may be glued onto the wheel.
Any grease or lube may be used to lubricate gears or moving parts.
Any Tamiya Hi-Torque Servo Saver is Permitted.
It’s permitted to mix & match front and rear wheels on the truck for durability.
Batteries: Any stick-pack type, hard round case LiPO, NiCD, or Ni-MH is permitted. Examples: Reedy Wolf-Pack or Peak Racing Powermax batteries.